Outdoor Lighting Accessories

Outdoor Lighting Accessories

Behind every outdoor lighting scheme is a set of drivers, transformers and installation parts that matter just as much as the fittings themselves. Collingwood's constant current LED drivers, rated IP20 or IP65, cover outputs from 1W to 36W, some with mains dimming, while Hunza's buriable transformers are built to be installed below ground alongside a low voltage circuit. Glare guards and ground light installation tubes round out the range for a clean, professional finish. Always match a driver's output to your fittings, and use a qualified electrician for installation.

Filters

Sort by:

202 products

Wiska MP GEL 1000 two component gel in two white containers labelled A and B with black caps
Wiska Gel 10 litre MP-GEL1000W Sale price£376.20 inc. VAT
Stone Globe ground spike fixed to the base plate of a sandstone coloured stone effect globe on a lawn
Ground Spike for Stone Globes Sale price£32.00 inc. VAT
Collingwood JB2 waterproof junction box in blue plastic, shown at an angle on a white background with four yellow cable glands, and a printed wiring diagram on the housing marking the single IN port, three OUT ports, and the IP68 rating
Collingwood stainless steel bollard bracket shown on its own, a square base plate with two upright side plates and the two long fixing bolts laid in frontCollingwood stainless steel bollard bracket installed, bolted to a hard surface with a timber bollard post clamped between the side plates and secured with bolts
Collingwood LSD6024 60W 24V LED driver, a white rectangular polycarbonate unit shown at an angle, with mounting tabs at each end and a printed label showing input, output and CE certification details
Non dimmable LPC-35-700 LED driver in a white waterproof case with blue and red cables
LuxR Replacement Modux 2 LED, round metal board with a multi chip LED and a single pin, on a white background
LuxR Replacement Modux 2 LED Sale price£60.00 inc. VAT
Assorted brass, steel and grey plastic cylindrical canister housings of different sizes on a white background
Hunza Canisters Sale priceFrom £50.00 inc. VAT
Collingwood JB6 inline cable connector, close up of the black plastic housing with the single retaining screw and cable running in from each end
Collingwood handheld RF remote control in matte black, front view showing the circular RGB colour wheel with central white light button, numbered zone buttons 1 to 4, brightness and power controls, and three programmable scene buttons
Plain studio shot on a white background of the Collingwood PLD UNI-DRIVE LED driver, angled from above. Slim rectangular white plastic casing with a moulded fixing tab and keyhole slot on the near edge. The top face is printed with the Collingwood logo, the PLD UNI-DRIVE name, a CE mark and small technical print including a DIP switch diagram for the 350mA and 700mA settings. Terminal markings along the right edge read SYNC, SEC, 1-10V and PUSH with L and N, under a removable screwed end cover.
Hunza Hex Cell Louvre Adaptor in black with a honeycomb grid and red seal ring, seen from aboveDimension diagram for the Hunza Hex Cell Louvre Adaptor showing 63.5mm width and 11mm depth
White Ecopac Power TRIAC dimmable LED driver with label, terminal block and removed cover, white background
Plain studio shot on white of a finned extruded aluminium LED driver, viewed at a three quarter angle from above. Silver grey ribbed casing with flat end mounting brackets, keyhole fixing slots and black flying lead cables emerging from both ends. The printed label on the top face reads IP66 alongside the model marking ELED-60-24V and Ecopac Power branding, with output figures of 24V DC and 60W.
Collingwood PDC INT 1-10V dimmable interface, white and blue plastic module with terminal blocks and printed label
Hunza Pure LED RD replacement driver, a round white constant current unit with red and black output leads and a grey cable
Harte FF02 medium foundation frame, galvanised steel square frame with four threaded bars, studio shotHarte FF02 medium foundation frame dimensions drawing, 150mm square and 200mm tall
Angled studio shot of the slimline white plastic PSMD3024 LED driver on a plain white background, with a printed specification label and Ecopac Power branding across the top face, a loading 60 to 100% panel at the far end, and a recessed terminal opening beside two screw fixing holes at the near end.
Collingwood 2 core rubber cable, close up of the stripped end showing the black rubber outer sheath and red and black insulated copper conductors
Orluna M-100 100mA mains dimmable LED driver, 7.2W output
Orluna M-300 300mA mains dimmable LED driver, 14W output
Hunza Glare Guard in solid copper with an angled cut top, shown on a white studio backgroundDimension diagram for the Hunza copper Glare Guard showing 70mm height and 63.5mm width
Hunza Glare Guard - Copper Sale price£66.00 inc. VAT
Angled view of the Collingwood JB1 waterproof junction box in blue plastic, showing four yellow cable glands, one marked IN and three marked OUT, with the parallel wiring diagram, input rating and IP68 mark printed on the lid.
Wise dusk to dawn sensor, white wall mounted housing with a small dark light sensor window, angled front viewWise dusk to dawn sensor in white plastic, rear mounting plate with fixing slots, shown at an angle
Collingwood DMX2102 RGBW/RGB DMX decoder, angled view on a white studio background showing the DC input and DMX terminals on the left, the digital channel display and Collingwood logo in the centre, and the RGBW output terminals on the rightCollingwood DMX2102 RGBW/RGB DMX decoder product cutout, same angled view of the plastic housing with terminal blocks and digital channel display, isolated on a transparent background
Wise 240V transmitter, small white module with yellow warning triangle, three coloured wires and white aerial, angled viewWise 240V transmitter, front of the white module showing the warning label, rating label and brown, blue and black wires
Wise Transmitter 240V - 2 Channel Sale price£70.00 inc. VAT
Hunza replacement lamp holder, a white ceramic bi pin socket with two short wires, on a white background
Hunza Replacement Lamp Holder Sale price£21.00 inc. VAT
LuxR Replacement Modux 4 LED, round white board with a multi chip LED and two pins, on a white background
LuxR Replacement Modux 4 LED Sale price£78.00 inc. VAT
LuxR Replacement Modux 1 LED, round white board with a single warm white LED and one pin, on a white background
LuxR Replacement Modux 1 LED Sale price£43.00 inc. VAT
Hunza T-LD25W 25 watt LED driver, a black oval IP66 housing with a green rating label, on white
Collingwood UY2 gel filled connector, close up studio shot on a white background showing the translucent plastic housing, cable entry sleeve and amber pressure cap that seals the joint.
Black finned metal LED driver photographed at an angle on a plain white studio background, with a short mains lead leaving one end, two output leads leaving the other, flat fixing flanges with screw holes at the corners, and a white printed specification label with CE marks across the top face.
Collingwood PR3011 power repeater at a three quarter angle on a plain white studio background. Slim white rectangular plastic case lying flat, with a printed label across the top reading PR3011 Power Repeater, the Collingwood logo, input and output ratings and CE and RoHS marks. Screw terminals run along both long edges, labelled DC input and signal in and out on one side and V+, R, G, B and W output on the other. A fixing screw sits at each end of the lid and the moulded end lugs are notched.
Collingwood PR3002 power repeater photographed at a three quarter angle on a plain white studio background, a slim rectangular white plastic module with a printed lid label reading PR3002 Power Repeater beside the Collingwood logo, rows of screw terminals along both long edges marked DC input, signal input and RGBW output, and a flat fixing lug with a screw at each end.
Orluna L-N-20 24V DC non dimmable LED driver, 20W output
Orluna 0-120 EldoLED 0 to 10V dimmable LED driver, 120mA 20W

Behind every well specified outdoor lighting scheme is a set of drivers, transformers and installation parts that never get seen once the job is finished but matter just as much as the fittings themselves. This collection covers the technical accessories that keep an outdoor lighting installation running properly.

Drivers and transformers

Collingwood's range of constant current LED drivers, including the DRV150700 and DRV350700TD, are rated IP20 or IP65 depending on the model and cover outputs from 1W up to 36W, with some versions offering mains dimming. Hunza's buriable transformers are built specifically to be installed below ground alongside low voltage garden lighting circuits.

Installation accessories

Beyond drivers, this collection also includes glare guards to soften the beam of a spike or spot light, and ground light installation tubes for a clean, professional recessed fitting.

Good to know

  • Always match a driver's output current and wattage to the exact fittings it will power, and have all outdoor electrical installation carried out by a qualified electrician.

We're Proud To Offer

Collingwood Lighting logoHunza Lighting logoOrluna logoSchwung logoBuster + Punch logo