Collingwood WL041 IP Straight to Mains Fan Effect LED Wall Light - Anodised Aluminium

A Wall Light That Paints With Light

The WL041 IP is not there to flood a space with light. It is there to be looked at. A compact aluminium disc holds over a hundred fine radiating fins, and once the integrated LED is switched on it throws a striking fan shaped burst of light across the wall, ceiling or floor beside it. It suits a spot where the pattern itself is the feature, an entrance, a covered walkway or a garden wall after dark.

Anodised Aluminium, Built For The Elements

This version is finished in anodised aluminium, a hard wearing surface that keeps its silvery tone outdoors without flaking or corroding the way a painted finish can. The fins are pressed from the same material as the body, so the whole fitting reads as one solid disc rather than a light with a separate shade bolted on. It works well against render, brick or stone, and pairs naturally with other aluminium or stainless steel exterior fittings nearby.

How It Works

The WL041 IP wires straight to mains, with the driver built into the fitting itself, so there is no separate transformer or driver box to find space for. It comes with a mounting bracket and waterproof crimp connectors, and the wiring is parallel, which means several units can be looped off the same circuit rather than each needing its own dedicated run back to the switch. The LED is fixed at 1.6W and is available as 3000K warm white, rated up to 33 lumens, or 4000K neutral white, rated up to 37 lumens. Because the light source is built in rather than a swappable lamp, the fitting is designed to run for the long term without maintenance.

Rated IP65, the WL041 IP is sealed against dust and jets of water, which makes it suitable for exterior walls and also for bathroom lighting zones 1 and 2. Read our guide to bathroom lighting zones if you are placing it near a shower or bath.

Where It Works Best

Outdoors, it earns its keep on a porch, a garden boundary wall, either side of a front door or along a covered terrace, anywhere the fan of light can fall across a plain surface rather than being lost against foliage. It is equally at home indoors as a wet room or bathroom feature light, mounted low on a tiled wall where the starburst pattern plays across the surface. Because the output is modest, it is best used as a decorative accent or wayfinding light rather than as the main source of illumination in a space.

About Collingwood Lighting

Collingwood Lighting designs and builds its LED fittings from its base in Sywell, Northamptonshire, and has worked exclusively in LED technology since 2002. The brand states it was among the first to bring fire rated, fully sealed for life and mains dimmable LED products to the UK electrical wholesale market, helping shift trade lighting away from halogen earlier than many rivals. Collingwood has also been awarded an EcoVadis Gold medal, placing it in the top five per cent of companies assessed globally for sustainability.

Good To Know

• Backed by a 7 year Collingwood warranty.
• Rated IP65, suitable for outdoor walls and for bathroom zones 1 and 2.
• Class I electrical, so the fitting must be properly earthed on installation.
• Not dimmable. There is no dimmable version of this fitting.
• The LED is integrated and cannot be replaced separately from the fitting.
• Wiring is parallel, allowing several units to be run from one circuit.
• Wipe clean with a soft, dry cloth. Avoid abrasive or solvent based cleaners on the anodised finish.
• Moonlight Design recommends installation by a registered NICEIC electrician.

Questions People Ask

• Is the Collingwood WL041 IP dimmable? No, the WL041 IP is a fixed output fitting and is not compatible with any dimmer switch.
• Can the WL041 IP be fitted in a bathroom? Yes, it is rated IP65, which covers use in bathroom lighting zones 1 and 2 as well as fully exposed exterior walls.
• Does the WL041 IP need a separate transformer or driver? No, it wires straight to mains and has its driver built into the fitting, so no external transformer is needed.
• What colour temperatures is the WL041 IP available in? It is available in 3000K warm white, rated up to 33 lumens, and 4000K neutral white, rated up to 37 lumens.
• Can the LED in the WL041 IP be replaced if it fails? No, the LED is sealed into the fitting for life, so the light is designed to be replaced as a complete unit rather than relamped.

90mm diameter x 60mm depth

• Collingwood Decorative Light Guide 2025

We offer free standard delivery on orders within the UK Mainland* (an additional fee applies for the Isle of Wight, the Isle of Man, the Scottish Isles, parts of Scotland, Northern Ireland, the Republic of Ireland, the Channel Isles and International).

*Collingwood orders under £150 incur a delivery fee of £9.95 inc. VAT.
*Any order under £49 incurs a delivery fee of £9.95.